Iogear GWPAP1 User Manual

1Quick Start GuideNetShair NanoUltra Portable Wi-Fi Router/Access PointGWPAP1PART NO. Q1376www.iogear.com

101. Make sure the NetShair_Nano_XXXX Wi-Fi Network is connected.2. After setting the NetShair Nano in Router Mode (see Router Mode Setting), tap

112. On the Home screen, tap Advance Settings.3. Tap Set Operation Mode and then tap Access Point.4. Tap Restart to save settings.5. After the NetSh

12Option 1: Wireless PasswordTo change the pre-shared network key, enter a new key with a minimum of 8 characters.1. Tap Basic Setting > Set Wirele

13NetShair Nano Setup AndroidDo not connect Ethernet cable until last step! (See Internet Connection)1. Make sure you have downloaded the NetShair

14Internet Connection AndroidRouter Mode SettingFollow the steps below to setup the NetShair Nano for Router Mode. If you are unsure about which mode

15Router Mode: DHCP (Default)1. On the Home screen, tap Advance Settings, then Set WAN Interface.2. By default the NetShair Nano is set to DHCP clien

161. Make sure the NetShair_Nano_XXXX Wi-Fi Network is connected.2. After setting the NetShair Nano in Router Mode (see Router Mode Setting), ta

175. After the NetShair reboots, connect an Ethernet cable. The Network LED indictor will light solid once a successful connection has been mad

18Wireless Security Settings AndroidOption 1: Wireless PasswordTo change the pre-shared network key, enter a new key with a minimum of 8 characters.1.

19NetShair Nano Setup Computer / OtherNote: Follow the steps below to setup NetShair Nano using the web client for computers or mobile devices with a

© 2014 IOGEAR® Part No. Q1376IOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR. Microsoft and Windows are registered trademar

20Internet Connection Computer / Other1. Make sure the “NetShair_Nano_XXXX” Wi-Fi network is connected. Open the Browser and enter 192.168.1.25

211. By default the NetShair Nano is set to DHCP client. If the network the NetShair Nano is connected to requires a username and password to

225. Once rebooted, connect an Ethernet cable from the modem to the NetShair Nano.6. Connect back to NetShair_Nano_XXXX Wi-Fi network. Open your w

23Access Point Mode SettingFollow the steps below to setup the NetShair Nano for AP Mode. If you are unsure about which mode to use, see Router Mode o

24Wireless Security Settings Computer / OtherOption 1: Wireless Password1. Make sure the “NetShair_Nano_XXXX” Wi-Fi network is connected. Open th

25Option 2: Network Name (SSID)1. Make sure the “NetShair_Nano_XXXX” Wi-Fi network is connected. Open the Browser and enter 192.168.1.254 into the a

26Hotel provides wired Internet access1. Do not connect the Ethernet cable until app/client setup is complete. 2. Power on the NetShair Nano by plu

27IC StatementIC Caution: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditio

28FCC StatementCE StatementThis product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the F

29WE’RE HERE TO HELP YOU! NEED ASSISTANCE SETTING UP THIS PRODUCT?Make sure you:1. Visit www.iogear.com for more product information 2. Visit www.iog

Table of ContentPackage Contents 4System Requirements 4Overview 4Charging 5Router Mode or AP Mode 5Hardware Installation 6Software Setup: Which device

© 2014 IOGEAR®

41 x Quick Start Guide1 x Warranty CardRS23564178Package ContentsSystem RequirementsOverview1 x NetShair Nano Wi-Fi Router/ Access Point• USB port o

5RSUSB pass-through charging port: connect to charge most smartphones and USB devices (1A maximum pass-through current).ChargingRouter Mode or AP Mode

or 11. To power on the NetShair Nano, plug into a USB port on your computer or to a USB charging adapter of any mobile device.2. Download the Net

7Do not connect Ethernet cable until last step! (See Internet Connection)1. Make sure you have downloaded the NetShair Nano App prior to setup! 2.

8Internet Connection iPod / iPhone / iPad Router Mode SettingFollow the steps below to setup the NetShair Nano for Router Mode. If you are unsure abou

91. On the Home screen, tap Advance Setting, then Set WAN Interface.Router Mode: DHCP (Default)2. The default setting is DHCP client. If the netw